Factory Supply Milling Type Cold Saw - Series circuit solid state high frequency welder – Tongze
Factory Supply Milling Type Cold Saw - Series circuit solid state high frequency welder – Tongze Detail:
Solid state high frequency power supply
At present, the high frequency welded pipe equipment designed and manufactured by our country adopts the single loop high frequency equipment of the electron tube oscillator. By adjusting the size of the anode voltage of the electron tube, the purpose of adjusting the high frequency output power is achieved. The high frequency welding pipe equipment of the electronic tube is not only low in efficiency and large in volume, but also in need of preheating before use and short service life of the electronic tube.
So the solid state high frequency power supply using power MOSFET to compose high frequency inverter is greatly improved in two aspects of capacity and frequency, besides some special applications, such as high frequency dielectric heating, solid state high frequency power supply can completely replace the high frequency power supply of electron tube, and become the representative of the new generation of induction heating power supply.
The main application field of high frequency and capacity solid state high frequency power supply is high frequency welding pipe industry,
Because of the existence of mutation in harsh conditions including sensor open circuit, short circuit of sensor and tube and so on in China's high frequency welded pipe industry, at the same time, the power supply of high frequency welded pipe is basically full load long term working system, so the application of solid state high frequency power supply in the welded pipe industry represents the highest level of design and manufacturing of solid state high frequency power supply.
Technical features of CXGP-C solid state high frequency welding machine
1. The rectifier switchgear and the inverter output cabinet are designed independently, and the soft cable is connected to facilitate the site layout of the users.
2. Selection of DC chopped wave rectifier to ensure the power factor is more than 0.92, the minimum relative harmonic content; Selection of the 12 pulse thyristor rectifier can eliminate the 5、7 harmonic of grid side and line side harmonic current minimum .
3. The inverter bridge uses power unit superposition to complete the power synthesis, and each MOSFET power unit is designed to be 50kW/100kW/150kW. The power unit is designed to be a slide type drawer structure, which is convenient for installation and maintenance.
4. High frequency welding machine equipment with high standard electromagnetic compatibility design, electromagnetic radiation meet the national standard.
5. The airtight chassis is designed to meet the demanding environment requirements of the user.
Full digital control system
1. The three-phase rectifier is controlled by single chip microcomputer with high performance cost to achieve accurate synchronization trigger, high control precision and small non characteristic subharmonic on the net side.
2. The resonant inverter uses CPLD to form a full digital control system, which is automatically fixed angle, with high phase locking precision and wide phase locked range.
3. The welding machine has the function of electronic automatic load matching, the load adaption ability is strong, the electric efficiency is high, and the power factor is high.
4. The high frequency welding machine has perfect protection function, reliable work and low failure rate.
Man-machine interface and fault diagnosis system
1. The PLC+ touch screen to form the perfect man-machine interface system.
2. The automatic control of the welding machine system is realized.
3. Fault display and fault diagnosis system.
Main technical indicators
|
Welding machine model |
AC input |
Rated DC voltage |
Rated DC current |
frequency range |
Electric efficiency |
working condition |
|
CXGP60-0.8-H |
3AC380V |
450V |
130A |
650~ |
≥85% |
continuous |
|
CXGP100-0.45-H |
3AC380V |
450V |
220A |
400~ |
≥85% |
continuous |
|
CXGP150-0.4-H |
3AC380V |
450V |
330A |
350~ |
≥85% |
continuous |
|
CXGP200-0.35-H |
3AC380V |
450V |
440A |
300~ |
≥85% |
continuous |
|
CXGP250-0.3-H |
3AC380V |
450V |
550A |
250~ |
≥85% |
continuous |
|
CXGP300-0.3-H |
3AC380V |
450V |
660A |
250~ |
≥85% |
continuous |
|
CXGP400-0.3-H |
3AC380V |
450V |
880A |
250~ |
≥85% |
continuous |
|
CXGP500-0.2-H |
3AC380V |
450V |
1100A |
150~ |
≥85% |
continuous |
|
CXGP600-0.2H |
3AC380V |
450V |
1300A |
150~ |
≥85% |
continuous |
|
CXGP700-0.2-H |
3AC380V |
450V |
1500A |
150~ |
≥85% |
continuous |
|
CXGP800-0.2-H |
3AC380V |
450V |
1800A |
150~ |
≥85% |
continuous |
|
CXGP1000-0.2-H |
3AC380V |
450V |
2200A |
150~ |
≥85% |
continuous |
|
CXGP1200-0.2-H |
3AC380V |
450V |
2700A |
150~ |
≥85% |
continuous |
|
CXGP1400-0.15-H |
3AC380V |
450V |
3100A |
100~ |
≥85% |
continuous |
|
CXGP1600-0.15H |
3AC380V |
450V |
3600A |
100~ |
≥85% |
continuous |
|
CXGP1800-0.15-H |
3AC380V |
450V |
4000A |
100~ |
≥85% |
continuous |
Conventional design. It can be customized according to the power grid level, process demand and working frequency
Reference for selection of equipment
|
Welding machine model |
Welded pipe specification |
Pipe type |
Welding speed |
Welding method |
Cooling mode |
Remarks |
|
CXGP60-0.8-H |
pipe diameter: φ6~φ20mm wall thickness: 0.15~0.5mm |
Circular tube Moment tube Special-shaped tube |
60~100m/min |
induction welding |
Water-water Air-water |
Steel pipe Copper pipe Aluminum tube Stainless steel |
|
CXGP100-0.45-H |
pipe diameter: φ16~φ45mm wall thickness: 0.6~1.5mm |
Circular tube Moment tube Special-shaped tube |
60~100m/min |
induction welding |
Water-water Air-water |
Steel pipe Aluminum tube Stainless steel |
|
CXGP150-0.4-H |
pipe diameter: φ20~φ60mm wall thickness: 0.6~1.5mm |
Circular tube Moment tube Special-shaped tube |
60~ |
induction welding |
Water-water Air-water |
Steel pipe Aluminum tube |
|
CXGP200-0.35-H |
pipe diameter: φ45~φ76mm wall thickness: 1.5~3.25mm |
Circular tube Moment tube Special-shaped tube |
60~ |
induction welding |
Water-water Air-water |
Steel pipe |
|
CXGP250-0.3-H |
pipe diameter: φ45~φ89mm wall thickness: 1.5~4.0mm |
Circular tube Moment tube Special-shaped tube |
60~ |
induction welding |
Water-water Air-water |
Steel pipe |
|
CXGP300-0.3-H |
pipe diameter: φ50~φ114mm Square tube: 200×200mm |
Circular tube Moment tube Special-shaped tube |
induction welding ≥40m/minContact welding ≥50m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP400-0.3-H |
pipe diameter:φ114~φ156mm Square tube: 200×200mm wall thickness: 4.0~8.0mm |
Circular tube Moment tube Special-shaped tube |
induction welding ≥25m/min Contact welding ≥30m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP500-0.2-H |
pipe diameter:φ165~φ219mm Square tube: 200×200mm~300×300mm wall thickness: 4.0~12.0mm |
Circular tube Moment tube Special-shaped tube |
induction welding ≥ 14m/min ≥ 18m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP600-0.2-H |
pipe diameter:φ219~φ273mm Square tube: 200×200mm~300×300mm wall thickness: 6.0~12.0mm |
Circular tube Moment tube Special-shaped tube |
induction welding ≥ 15m/min Contact welding ≥ 18m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP800-0.3-H |
pipe diameter:φ325~φ508mm Square tube: 300×300mm~400×400mm wall thickness: 6.0~16.0mm |
Circular tube Moment tube Special-shaped tube |
induction welding ≥ 7m/min Contact welding ≥ 9m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP1000-0.2-H |
pipe diameter:φ325~φ610mm Square tube: 300×300mm~500×500mm wall thickness: 4.0~16.0mm |
Circular tube Square tube Moment tube |
induction welding ≥7m/min Contact welding ≥ 9m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP1200-0.2-H |
pipe diameter:φ325~φ610mm Square tube: 300×300mm~500×500mm wall thickness: 4.0~16.0mm |
Circular tube Square tube Moment tube |
induction welding ≥8m/min Contact welding ≥ 10m/mi |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP1400-0.15-H |
pipe diameter:φ325~φ610mm Square tube: 300×300mm~500×500mm wall thickness: 4.0~16.0mm |
Circular tube Square tube Moment tube |
induction welding ≥10m/min Contact welding ≥ 13m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP1600-0.15-H |
pipe diameter:φ325~φ610mm Square tube: 300×300mm~500×500mm wall thickness: 4.0~20.0mm |
Circular tube Square tube Moment tube |
induction welding ≥7m/min Contact welding ≥ 10m/min |
induction welding Contact welding |
Water-water Air-water |
Steel pipe |
|
CXGP1800-0.15-H |
pipe diameter:φ325~φ610mm Square tube: 300×300mm~500×500mm wall thickness: 4.0~20.0mm |
Circular tube Square tube Moment tube |
induction welding ≥7m/min Contact welding ≥ 10m/min |
Model Selection Description
CXGP-B/100-0.15- FG
1 2 3 4
Annotation:
1. Series of code: CX series GP
2. Topology mode: B - parallel type, C- series type
3. Equipment power: 60~1800KW
4. Device frequency: 0.15-0.8
5.Equipment use: FG square tube, YG tube, TG copper tube, LG aluminum tube and so on
Product detail pictures:
Related Product Guide:
We have been ready to share our knowledge of advertising worldwide and recommend you suitable products at most aggressive costs. So Profi Tools present you ideal price of money and we've been ready to create with each other with Factory Supply Milling Type Cold Saw - Series circuit solid state high frequency welder – Tongze , The product will supply to all over the world, such as: Slovakia , Armenia , London , We supply skilled service, prompt reply, timely delivery, excellent quality and best price to our customers. Satisfaction and good credit to every customer is our priority. We focus on every detail of order processing for customers till they have received safe and sound items with good logistics service and economical cost. Depending on this, our products and solutions are sold very well in the countries in Africa, the Mid-East and Southeast Asia. Adhering to the business philosophy of ??customer first, forge ahead', we sincerely welcome clients from at home and abroad to cooperate with us.
By Erin
from Bolivia
- 2017.03.28 16:34
We have been appreciated the Chinese manufacturing, this time also did not let us disappoint,good job!
By Lee
from Florida
- 2018.12.28 15:18
Related products
-
Chinese wholesale Automatic Packaging Machine -...
High-output solid-state welders More output: Continuous electronic load matching secures full power output across a wide range of tube sizes. More uptime: Short-circuit-proof, safe and reliable operation. Unrivalled efficiency: Diode rectifier with a constant power factor of 0.95 at all power levels, and an efficiency factor of 85-87%. Eco and energy friendly: High efficiency saves energy and reduces cooling water consumption. Easy to operate: An easy-to-use control panel with a mini...
-
Wholesale Square Pipe Making Machine - Straigh...
ERW Steel Pipe Mill description: ERW Tube mill/Pipe mill/welded pipe production/pipe making machine is used to produce round, square and Application: GI, construction, automotive, general mechanical tubing, furniture, agriculture, chemistry, oil, gas contructure. ERW Steel Tube Mill Advantage: • High production efficiency, • High automation • High strength, the machine works stably at a high speed, which improves product quality. • Low defective product rate • Save roller changing time • Save...
-
Reasonable price Fast Recovery Epitaxial Diode ...
High-output solid-state welders More output: Continuous electronic load matching secures full power output across a wide range of tube sizes. More uptime: Short-circuit-proof, safe and reliable operation. Unrivalled efficiency: Diode rectifier with a constant power factor of 0.95 at all power levels, and an efficiency factor of 85-87%. Eco and energy friendly: High efficiency saves energy and reduces cooling water consumption. Easy to operate: An easy-to-use control panel with a mini...
-
Chinese wholesale Automatic Packaging Machine -...
High-output solid-state welders More output: Continuous electronic load matching secures full power output across a wide range of tube sizes. More uptime: Short-circuit-proof, safe and reliable operation. Unrivalled efficiency: Diode rectifier with a constant power factor of 0.95 at all power levels, and an efficiency factor of 85-87%. Eco and energy friendly: High efficiency saves energy and reduces cooling water consumption. Easy to operate: An easy-to-use control panel with a mini...
-
Chinese Professional Cold Cut Flying Saw - Ser...
Solid state high frequency power supply At present, the high frequency welded pipe equipment designed and manufactured by our country adopts the single loop high frequency equipment of the electron tube oscillator. By adjusting the size of the anode voltage of the electron tube, the purpose of adjusting the high frequency output power is achieved. The high frequency welding pipe equipment of the electronic tube is not only low in efficiency and large in volume, but also in need of preheating ...
-
Best Price for Tube Mill Machine - Straight se...
ERW Steel Pipe Mill description: ERW Tube mill/Pipe mill/welded pipe production/pipe making machine is used to produce round, square and Application: GI, construction, automotive, general mechanical tubing, furniture, agriculture, chemistry, oil, gas contructure. ERW Steel Tube Mill Advantage: • High production efficiency, • High automation • High strength, the machine works stably at a high speed, which improves product quality. • Low defective product rate • Save roller changing time • Save...
